Nobelium 10
Nobelium 12
Nobelium 15
ULTIMATE Nobelium
SERIES SUBWOOFERS
*Nobelium is a radioactive metal with atomic number 102. It is named after the Swedish scientist Alfred Nobel
WELCOME
SUBWOOFER ENCLOSURES, GENERAL
Thank you for buying a DLS ULTIMATE Nobelium subwoofer.
The subwoofer must be installed correctly in order to work well.
This manual will show you how to install it like a pro. Please
read the entire manual before beginning the installation.
Install the subwoofer yourself if you feel confident with our
instructions and if you have the proper tools. However if you
feel unsure, turn over the installation job to someone better
suited to it.
Build your enclosure in a stable and airtight material. The best
is MDF-board, 19 mm, or particle board, 22 mm. Larger
enclosures must have bracing inside to avoid vibrations. The
enclosure must be completely airtight. Use sealing compound
in all joints, also around the cable terminals. The size of the
enclosure is decided by the speaker data.
SEALED ENCLOSURES
The speakers are designed for enclosure mounting. In "open
air" installations the power handling capacity is reduced by 30%
from the nominal value. We dont recommend ”open air”
installations for Ultimate Nobelium subwooers.
Sealed enclosures are easy to build. The size is not critical, but
it can´t be too small. The speaker data such as Fs, Qts, Vas
and X-max decides the size of the enclosure.
Large speakers need larger boxes. Two speakers need a box
of the double size etc. The enclosure must be completely air-
tight.
A sealed enclosure should be filled with acoustic wool up to 75
- 100%.
A sealed enclosure has a lower efficiency than vented
enclosures but they can handle high power and are easy to
build.
CONNECTION OF SUBWOOFER
How to connect depends on what type of amplifier you use.
The best is to follow the instructions given in the manual for the
amplifier. Most amplifiers today have built-in lowpass crossover
and possibilities to connect your subwoofer in bridge mode.
Two 4 ohm subwoofers are often connected in stereo mode
since most amplifiers can´t handle bridge mode loads below 4
ohms.
A subwoofer in a sealed enclosure creates a tight bass suitable
for the audiophiles listening to classical music, jazz and soft
rock. The Nobelium subwoofers can be used in sealed
enclosures.
The Iridium subwoofers have dual, four ohm, voice coils. Each
voice coil has an impedance of 4 ohms. If they are connected in
series the resulting impedance is 8 ohms. If they are connected
in parallel the resulting impedance is 2 ohms. Make sure to
connect in a way that don´t ruin the amplifier. If you have a DLS
Ultimate amplifier it´s possible to connect the voice coils in
parallel, these ampliers are 1 ohm stable.
VENTED ENCLOSURES
A speaker in a vented enclosure has a higher efficiency (3 dB)
and higher power handling capacity than in a sealed enclosure.
In a vented enclosure the sound from the speaker and the port
work together creating a higher sound level. The sound from
the port must come out in the same phase as from the speaker
otherwise the result is bad.
We also recommend the use of a subsonic highpass filter. This
gives a better bass reproduction with less "rumble". In most
DLS amplifiers this feature is already built-in.
The size of the vented enclosure is decided by the speaker
data just as for the sealed one.
For wiring use high class speaker wires, minAWG13 (2.5 mm2).
The size of the vehicle often decides the practical size of the
enclosure. Asmaller enclosure has a higher resonant frequency
than the larger one. The size of the enclosure should not be so
big that the speaker plays below it´s own free air resonance
(Fs), if so the power handling capacity drops.
The port does not have to be fully inside the enclosure as long
as the area and length are correct. Sometimes you need two or
more ports in an enclosure. You can convert from one to two or
more ports as long as the total port area is the same.
All Nobelium subwoofers can be usedl in vented boxes.
For example DLS SC 2x4.
If you have an amplifier without built-in crossover you must use
a passive crossover between amplifier and subwoofer like in
this example, one crossover for each voice coil.
Component values are for 4 ohms.
+
L
C
BANDPASS ENCLOSURES
-
In all bandpass enclosures the speakers are hidden inside the
enclosure, all sound is coming out through the ports. There are
different types of bandpass enclosures and they have in com-
mon that they are a bit more difficult to build. DLS Iridium
subwoofers can be used in bandpass enclosures.
Connected with a 12 dB passive low-pass x-over = 10 mH coil
in series and a bipolar capacitor of 300 microFarad in parallel.
Crossover frequency is 95 Hz.
Active filter
Amplifier
IMPORTANT!
Think of the speaker weight when you install it. If you don´t
mount it properly it can come loose.
Connection in mono bridge mode with an active x-over. Voice
coils connected in series. If you have a 1 ohm stable amplifier
the voice coils should be connected in parallel for best
performance (for example on a DLS monoblock).
Valid from 2005-07-04
RECOMMENDED ENCLOSURES FOR Nobelium10, 12 and 15
VENTED ENCLOSURES
F3 = approximative lower frequency for vented
RUNNING-IN PERIOD
Allow the speaker to play for at least 15-
20 hours. After this time the
performance is correct.
VENTED BOX
boxes in Hz. Often called F-3 dB point = the point
where the power is 50% lower.
Fb = Box resonant frequency
Sub Connection
Volume (litre/ft3)
Port
3” x 18 cm/7,1”
3” x 25,7 cm / 10”
4” x 29 cm/ 11,4”
4” x 32 cm / 12,6”
Damping
Line inside
Line insida
Line inside
Line inside
F3
Fb
10”
12”
12”
12”
15”
VC in parallel
Single VC
VC in series
VC in parallel
VC in parallel
31,65 / 1,1
34,4 / 1,21
35,87 / 1,26
46,10 / 1,1
56,5 / 1,99
39,3 Hz
33,7 Hz
46,4 Hz
37,3 Hz
50,2 Hz
39,0 Hz
33,0 Hz
45,0 Hz
36,9 Hz
45,0 Hz
2x4” x 40 cm / 15,7” Line inside
SEALED BANDPASS
Nobelium10 (VC:s in parallel to 2 ohm)
Vb1
20,1
Vb2
17
Port Vb2
2 x6,8 x 27,6 cm
0,71 ft3 0,60 ft3 2 x 3" x 10,8" (US)
F3 Vb1: 44,8 Hz, Vb2: 86,6 Hz
Nobelium12 (VC:s in parallel to 2 ohm)
Vb1
Vb2
Port Vb2
24,46 32,12 2 x10,2 x 27 cm
0,86 ft3 1,13 ft3 2 x 4" x 10,6" (US)
F3 Vb1: 45 Hz, Vb2: 94 Hz
Vb1=rear chamber,
Vb2=front chamber
Nobelium12 (Single VC, 4 ohm)
Vb2
23,95 22,37 1 x10,2 x 29 cm
0,84 ft3 0,79 ft3 1 x 4" x 11,4" (US)
F3 Vb1: 38,5 Hz, Vb2: 79 Hz
The speaker is installed in Vb1
playing into chamber Vb2 where the
port(s) are installed.
Vb1
Port Vb2
SEALED ENCLOSURES
Nobelium10, single VC:
28 litres / 0,99 ft3
F3: 52,7 Hz
Nobelium10, dual VC in parallel:
17,4 litres / 0,61 ft3
F3: 73,4 Hz
SEALED BOX
Nobelium 12, single VC:
23,2 litres / 0,82 ft3
F3: 51,9 Hz
Nobelium 15, single VC:
45 litres / 1,59 ft3
F3: 51,5 Hz
Nobelium 12, dual VC in parallel:
43,72 litres / 1,54 ft3
F3: 52,4 Hz
Nobelium 15, dual VC in parallel:
40 litres / 1,41 ft3
F3: 64,5 Hz
HINTS & TIPS FOR ”DO IT YOURSELF” ENCLOSURE BUILDERS
ENCLOSURE PLACING IN DIFFERENT TYPES OF
VEHICLES
In small vehicles like VW Golf, Peugeot 306 and similar the
bass box should be installed with both speaker and port directed
backwards.Alternatively booth speaker and port can be directed
upwards. This way of mounting is valid for all types of vehicles
where the trunk is incorporated with the inner compartment.
ABOUT THE RECOMMENDED ENCLOSURES
The performance of these recommended enclosures will vay
from vehicle to vehicle. It is more difficult to get a tight and well
defined bass in a SEDAN vehicle because of the tightness
between trunk and interior of the vehicle. In this case a band-
pass box could be a better choise.
- All volumes are inside measures.
- Volumes occupied by speaker and ports have already been
added to the given enclosure volumes.
- Use conical bass ports for best result. (DLS BP-75 or BP-
110). If the ports are too long for the box you can use a bend.
Either cut the tube and glue it together in angle, or use factory
made tube bends. It´s easier to use the factory made ones. The
total length must be the same as for a straight tube. Make the
measure in the center of the tube.
In sedan vehicles with the passenger compartment separated
from the trunk, the enclosure should be installed with booth
speaker and port directed towards the rear seat. Some cars
have an opening in the middle of the rear seat for loading skis
etc. You can install the enclosure behind this opening and direct
speaker or port through this opening. There must be some free
space in front of the port, (between the rear seat and the port
opening).
The port opening inside the enclosure must not be closer to an
interior wall than 3” (75 mm), otherwise it will have negative
effects on the airflow.
- The enclosure must be very steady and completely air-tight.
Use 22 mm particle board or 19 mm MDF-board. The particle
board has a self resonant frequency of 14 Hz while the MDF
has a resonant frequency of approx. 400 Hz. It´s important to
do some type of bracing inside the enclosure to avoid vibrations.
Volume taken up by bracing should be added to the enclosure
volumes.
In large vehicles like station wagons the best sound is achieved
with the enclosure installed behind the rear seat with booth spea-
ker and port directed backwards. Alternatively you can install
the enclosure on one side of the luggage compartment.
CALCULATE YOUR ENCLOSURE
Box volumes:
When caculating the volume of an enclosure you simply multiply
the width (W) x heigth (H) x depth (D).
Use measures in dm and you will get the answer in liters.
A trapezoid box is calulated as below:
ENCLOSURE DAMPING
Most enclosures should be damped inside with syntetic
(acoustic) wool or damping mat (line). Attach the damping ma-
terial on the wall opposite from the speaker and port. A sealed
enclosure should be filled up to 70-100% with acoustic wool.
In a vented enclosure the speaker and port should be on the
same side, otherwise a fade-out of some frequencies can occour.
In most vehicles, except for SEDAN cars, the speaker and port
should be directed backwards for best result.
Vol=width (W) x heigth (H) x upper depth (UD) + lower depth (LD)
2
B
ÖD
Be sure to measure the
inside dimensions.
H
ND
upper
suspension
THE SUBWOOFER
WARRANTY SERVICE
This speaker is covered by warranty, depending on the
conditions in the country where it is sold. If the speaker is retur-
ned for service, please include the original dated receipt with
the product.
cone
spider
dust cap
chassis
voice coil
magnet
pole plate
T-yoke
ꢀ Technical Assistance
For technical assistance ask the shop where the product was
sold or the distributor in your very country.You can always phone
the DLS Helpdesk in Sweden + 46 31 840060 or send an e-
mail to [email protected]
DLS Svenska AB
P.O. Box 13029
SE-40251 Göteborg, Sweden
Tel: +46 31 840060
Fax: +46 31 844021
E-mail: [email protected]
We follow a policy of continuous advancement in development.
For this reason all or part of specifications & designs may be
changed without prior notice.
|