Previous Menu
USER'S
MANUAL
FA120C Security System
N5100-3V3 9/96
(continued)
TABLE OF CONTENTS
DISARMING THE SYSTEM AND SILENCING ALARMS (Using the 1 OFF Key).............................................20
USING THE KEYSWITCH...........................................................................................................................21
CHIME MODE (Using the 9 CHIME Key) ........................................................................................................22
PANIC KEYS..............................................................................................................................................22
TESTING THE SYSTEM (Using the 5 TEST Key) ..........................................................................................24
TROUBLE CONDITIONS............................................................................................................................26
"Check" and "Battery" Displays.....................................................................................................................26
Power Failure ............................................................................................................................................27
Other Displays ..........................................................................................................................................28
FIRE ALARM SYSTEM, IF INSTALLED .....................................................................................................29
In Case of Fire Alarm...................................................................................................................................29
Silencing Fire Alarms ..................................................................................................................................30
NATIONAL FIRE PROTECTION ASSOCIATION RECOMMENDATIONS ON SMOKE DETECTORS...........31
EMERGENCY EVACUATION......................................................................................................................32
QUICK GUIDE TO ALARM SYSTEM FUNCTIONS......................................................................................33
SUMMARY OF AUDIBLE/VISUAL NOTIFICATIONS..................................................................................34
PROTECTION ZONES LIST.......................................................................................................................35
OWNER'S INSURANCE PREMIUM CREDIT REQUEST..............................................................................37
CANADIAN DEPARTMENT OF COMMUNICATIONS (DOC) STATEMENT ..................................................39
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS.........................................................40
IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS..................................................................41
THE LIMITATIONS OF THIS ALARM SYSTEM ..........................................................................................42
SERVICING INFORMATION ......................................................................................................................43
WARRANTY................................................................................................................................... Back Cover
This manual is a step-by-step guide that will aquaint you with the system's features and benefits. It defines the
components and their functions, describes their operation, and instructs you with normal and emergency procedures.
Keep this manual in a convenient place so that you can refer to it as necessary.
Ð3Ð
SYSTEM OVERVIEW
General Congratulations on your ownership of a First Alert Professional Security
System. You've made a wise decision in choosing it, for it represents the
latest in security protection technology today, including microcomputer
technology to monitor all system status.
Basically, this system offers you three forms of protection: burglary, fire
and emergency. Your system may consist of at least one keypad which
provides full control of system operation, plus various devices such as
door and window sensors and motion detectors. It may also include a
selected number of smoke or combustion detectors designed to provide
early warning in case of fire. Your system may also have been pro-
grammed to automatically transmit alarm or status messages over the
phone lines to a central alarm monitoring station.
Keypads Your keypads allow you to control all system functions and feature a
telephone style (digital) keypad and a Liquid Crystal Display (LCD) that
shows the nature and location of all occurrences and a built-in sounder
which sounds during alarms and troubles.
For additional information, see the following section: ABOUT THE
KEYPADS.
Zones Your system's sensing devices have been assigned to various "zones".
For example, the sensing device on your Entry/Exit door may have been
assigned to zone 01, sensing devices on windows in the master bedroom
to zone 02, and so on. These zone numbers will appear on the display
when an alarm or trouble condition occurs.
Ð4Ð
(continued)
SYSTEM OVERVIEW
Alarms When an alarm occurs, both the keypad and external sounders will sound,
and a message at the keypad will identify the zone(s) causing the alarm. In
addition, if your system is connected to a central monitoring station, an
alarm message will be sent. To stop the alarm sounding, you simply disarm
the system.
Fire Protection The fire protection portion of your security system (if used) is always on
and will sound an alarm if a fire condition is detected. Refer to the FIRE
ALARM SYSTEM section for important information concerning fire pro-
tection, smoke detectors and planning emergency exit routes from your
premises.
Burglary Protection The burglary protection portion of your system must be turned on or
"armed" before it will sense burglary alarm conditions and sound an alarm.
Your system can be armed in one of four modes: STAY, AWAY, INSTANT
and MAXIMUM. Refer to the ARMING THE SYSTEM sections for
instructions in using these modes of operation.
Your system also provides a CHIME mode for alerting you to the opening
and closing of doors and windows while the system is disarmed.
Memory Of Alarm When an alarm or trouble condition occurs, the keypad displays the
number(s) of the zone(s) that caused the problem, and displays the type
of alarm or trouble (ex. FIRE, ALARM, CHECK). The display remains until it
is cleared by entering the OFF sequence (security code + OFF key) twice.
If the paging feature has been programmed for your system, a pager will
respond to certain conditions as they occur in your system, and display
code numbers indicating the type of condition that has occurred, as follows:
Pager Notification
1811 = Trouble
1001 = Open
1911 = Alarm
1002 = Close
Check with your installer for additional information.
Ð5Ð
ABOUT THE KEYPADS
Keypad Types All commands and procedures described herein are illustrated for Fixed-
Word Display keypads, however, an Alpha Display keypad (with a 2-line
LCD display for more detailed protection point identification and system
status, but with similar commands and procedures) is available and might
have been used instead.
Keypad Styles Fixed-Word keypads are available in two styles, A and B, either of which
may have been used in your system. Although different in appearance,
both styles are functionally similar. The keypads on style B keypads are
located behind a flip-down door which can be removed, if desired. Words
Unless noted oth-
displayed on all Fixed-Word keypads are the same, except that their
location in the display window differs slightly with each style.
erwise, all proce-
dures in this man-
ual apply equally to
all keypad types
and styles.
Note: Style B keypads are equipped with a READY indicator in place of
the POWER indicator on style A keypads. The READY indicator is lit when
the system is ready for arming (no protection zones open). While the
system is disarmed, this indicator will go on and off as protection zones are
opened and closed.
STYLE A FIXED-WORD KEYPADS
STYLE B FIXED-WORD KEYPAD
NO AC
AWAY
AWAY
NO AC
CHIME
BAT
AWAY
NO AC
CHIME
BAT
BYPASS
STAY
ARMED
POWER
NOT READY
STAY
INSTANT
BYPASS
NOT READY
ALARM
CHECK
FIRE
ALARM STAY
CHIME BAT
CHECK INSTANT
FIRE
INSTANT
BYPASS
NOT READY
ALARM
CHECK
FIRE
A
OFF
AWAY
STAY
First Alert®
1
2
3
B
C
D
MAXIMUM
TEST
BYPASS
OFF
AWAY
STAY
PROFESSIONAL
A
C
B
D
4
5
6
ARMED
READY
1
2
3
ARMED
POWER
PROFESSIONAL
INSTANT
CODE
CHIME
MAXIMUM
4
TEST
BTPASS
6
7
9
8
5
READY
INSTANT
7
CODE
CHIME
0
#
OFF
1
AWAY
2
STAY
3
8
9
*
FIRST ALERT ®
READY
0
#
TEST
5
BYPASS
6
MAXIMUM
4
*
PANIC
CODE
8
INSTANT
7
CHIME
9
FA250KP
(KEYPAD
DOOR
READY
First Alert
FA310KP
Ð6Ð
0
#
FA200KP
*
Professional
REMOVED)
SUMMARY OF SYSTEM STATUS DISPLAYS
AWAY
All burglary zones, interior & perimeter, are
armed.
NO AC
CHIME
BAT
AWAY
STAY
INSTANT
BYPASS
STAY
Perimeter burglary zones, such as windows
and doors are armed.
00
00
00
ALARM
CHECK
FIRE
INSTANT
BYPASS
NOT READY
Perimeter burglary zones armed and entry
delay is turned off.
NOT READY
One or more burglary protection zones have
been bypassed.
STYLE A KEYPAD DISPLAY
Appears when burglary portion of the system
is not ready for arming (due to one or more
open protection zones).
NO AC
AWAY
AWAY
READY
NO AC
The burglary portion of the system is ready to
be armed.
00
BYPASS
NOT READY
CHIME BAT
ALARM
STAY
M STAY
Appears when AC power has been cut off.
System is operating on backup battery power.
CHECK INSTANT
FIRE
FIRE
AC
CHIME
BAT
Appears when AC power is present.
STYLE B KEYPAD DISPLAY
Appears when the CHIME feature is ON.
Low system battery (if no zone number is shown), or Low battery condition in a wireless
sensor (if zone number is also shown).
ALARM
CHECK
Appears when an intrusion has been detected and the system is armed (also appears
during a Fire alarm). Accompanied by the ID # of the zone in alarm.
Appears when a malfunction is discovered in the system at any time or if a fault is
detected in a FIRE zone at any time or in a DAY(Trouble)/NIGHT(Alarm) burglary zone
during a disarmed period. Accompanied by a display of zone number in trouble.
FIRE
Appears when a fire alarm is present. Accompanied by a display of the zone # in alarm.
Ð7Ð
SUMMARY OF KEYPAD FUNCTIONS
1. DISPLAY WINDOW: Displays protection zone ID
and system status messages.
9.
8
CODE KEY : Used to assign additional user
codes for other users of the system.
2.
1
OFF KEY : Disarms burglary portion of the sys-
tem, silences alarms and audible trouble
indicators, and clears visual display after
problem's correction.
10.
9
CHIME KEY : Turns CHIME mode on and off.
When on, the opening of windows or doors while
the system is disarmed will sound 3 beeps at the
keypad(s).
3.
4.
2
3
,
AWAY KEY : Arms the entire burglary system
perimeter and interior.
11.
12.
✴
READY KEY: Displays all open protection
zones.
STAY KEY : Arms perimeter portion of burglary
system only. Interior protection is not armed,
which allows movement within premises without
causing alarm.
#
KEY: "Quick Arm" key permits ARMING of the
system without use of a security code (if so
programmed)
.
13. KEYS 0Ð9: Used to enter your security code(s).
5.
6.
4
5
MAXIMUM KEY : Arms in manner similar to
AWAY mode, but without the entry delay feature,
thus providing maximum protection. An alarm will
occur immediately upon opening any protection
point, including the main door.
14. READY INDICATOR: (GREEN) Lit when the system
is ready to be armed (no faults present). While the
system is disarmed, this indicator will go on and off as
protection zones are closed and opened.
Note: On some keypads (Style A) there is, instead, a
POWER INDICATOR (GREEN) which is lit when AC
power is present. If the indicator is off, the system may still
be operating, but on its backup battery power. See Power
Failure in TROUBLE CONDITIONS section.
TEST KEY : Tests the system and alarm
sounder if disarmed. Refer to TESTING THE
SYSTEM section for test procedures.
7.
8.
6
7
BYPASS KEY : Removes individual protection
zones from being monitored by the system.
†Note: Keys
1
through
9
each perform their
INSTANT KEY : Arms in manner similar to
STAY mode, but without the entry delay feature.
Entering via the main door will cause an instant
alarm.
associated companion functions (OFF, AWAY, STAY, etc.)
when preceded by an entry of the security code (as
described later).
Ð8Ð
15. ARMED INDICATOR: (RED).
Lit when the system has been armed (STAY, AWAY
INSTANT or MAXIMUM).
1
NO AC
AWAY
BYPASS
NOT READY
CHIME BAT
16. INTERNAL SOUNDER:
ALARM STAY
17
3
CHECK INSTANT
FIRE
The built-in keypad sounder mimics the alarm
sounder during alarms, and will also "beep" during
certain system functions. (see SUMMARY OF
AUDIBLE/ VISUAL NOTIFICATION).
15
14
A
C
B
D
ARMED
4
17. EMERGENCY KEYS:
Individual keys A, B, and C (key D not used).
READY
2
STAY
OFF
AWAY
On some keypads, these keys are not present, and
the following key pairs may be available, instead, for
emergency functions:
6
1
2
3
TEST
5
BYPASS
MAXIMUM
4
5
6
7
✴
&
#
,
✴
&
1
,
#
&
3
CODE
8
INSTANT
7
CHIME
Some or all of these keys/pairs may be programmed
for panic functions by your installer (see PANIC KEYS
section).
9
10
16
READY
First Alert
0
#
*
9
Professional
IMPORTANT!:
When entering codes and commands, sequential
key depressions must be made within 2 seconds of
one another. If 2 seconds elapses without a key
depression, the entry is aborted and must be
repeated from its beginning.
8
11
13
12
STYLE B KEYPAD
Ð9Ð
SECURITY CODES
General At the time of installation, your installer programmed a personal four-digit
Master code, known only to you and yours. This code is used to perform
most system functions, including arming and disarming of the system. As an
additional safety feature, temporary user codes can be assigned (see next
page) for use by those not having a need to know the Master code. Note
that the Master code remains in effect even when other user codes are
assigned.
Duress Code This feature is intended for use when you are forced to disarm or arm the
system under threat. When used, the system will act normally, but can
Ask your installer if
"Duress" is active for
your system, and if so,
silently notify the central station of your situation, if that service has been
provided.
The Duress code is defined as user number 8.
check here:
Important: The Duress code is useful only when connected to a central
station.
Quick Arming If your system supports "Quick Arming", the "#" key can be pressed in
place of the security code when arming the system. The security code is
Ask your installer if
"Quick Arming" is active
for your system, and if
always required, however, when disarming the system.
so, check here:
Ð10Ð
SECURITY CODES
To Assign, Change, 1. Enter your Master code and press the CODE key.
or Delete
User Codes
2. Enter single-digit User Number (2Ð7) for which a code is to be
assigned, changed, or deleted.
3. If assigning or changing a user's code, enter the desired
4-digit code for use by that User Number. The keypad will beep once.
4-DIGIT USER CODES
It is recommended that
obvious codes such as
1 1 1 1 or 1 2 3 4 not be
assigned.
If deleting a user's code, perform steps 1 & 2 and stop. In a few
moments the keypad will beep once, indicating that the existing code
has been deleted.
To assign your Duress code, do the following:
Enter your [Master code] + [8] + [8] + [desired 4-digit code]. The keypad
will beep once.
Important:
Temporary users should not
be shown how to use any The Master code can be changed by the main user of the system. To
system function they do not
need to know (e.g., bypassing
protection zones).
change it, do the following:
Enter your [Master code] + [8] + [1] + [new Master code] + [new
Master code] again. The keypad will beep once.
B
D
A
C
THESE KEYS
NOT PRESENT
ON ALL
{
KEYPADS
STAY
OFF
AWAY
2
USE THE CODE
KEY TO ASSIGN
OTHER USER
CODES
1
3
BYPASS
6
TEST
MAXIMUM
4
5
CODE
INSTANT
7
CHIME
8
9
“QUICK ARM” KEY
(IF PROGRAMMED
)
READY
TYPICAL KEYPAD
#
0
*
Ð11Ð
ENTRY/EXIT DELAYS
General Information Your system has preset time delays, known as exit delay and entry delay.
When you arm your system, exit delay gives you time to leave through
the main door without setting off an alarm. Entry delay gives you time to
disarm the system when you reenter through the main door. The system
must be disarmed, however, before the entry delay period ends, or an
alarm will occur. The keypad will beep slowly during the entry delay
period, reminding you to disarm the system.
You can also arm the system with no entry delay at all by using either
INSTANT or MAXIMUM arming modes. These modes can provide greater
security while you are sleeping or while you are away for extended
periods of time.
See your installer for your delay times and record them here:
Exit Delay:
seconds
Entry Delay:
seconds
Ð12Ð
CHECKING FOR OPEN ZONES
Using the Before your system can be armed, all protected doors, windows and other
protection zones must be closed or bypassed (see BYPASSING
✴
READY Key
PROTECTION ZONES section), otherwise the keypad will display a "Not
Ready" message, and if your keypad has a READY indicator light, it will
not be lit. The READY key can be used to display all faulted zones,
making it easier for you to secure any open zone.
To display faulted zones, simply press and release the READY key (do
not enter code first). Secure or bypass the zones displayed before arming
the system.
A "Ready" message will be displayed when all protection zones have
been either closed or bypassed and the keypad's READY indicator light (if
present) will be lit.
TYPICAL DISPLAY
INDICATING OPEN PROTECTION ZONE
B
D
A
C
THESE KEYS
NOT PRESENT
ON ALL
{
AC
KEYPADS
02
STAY
OFF
AWAY
NOT READY
2
TO DISPLAY
OPEN ZONES,
PRESS THE
READY KEY
1
3
BYPASS
6
TEST
MAXIMUM
4
5
CODE
INSTANT
7
CHIME
8
9
READY
TYPICAL KEYPAD
#
0
*
Ð13Ð
BYPASSING PROTECTION ZONES
Using the This key is used when you want to arm your system with one or more
zones intentionally unprotected. The system must be disarmed first.
1. Enter your security code and press the BYPASS key.
6
BYPASS Key
LIMITATION
2. Enter zone number(s) for the zone(s) to be bypassed (e.g., 06, 10,
13, etc.). Single digit zone numbers must be preceded by a zero (e.g.
The system will not
allow fire zones to be
bypassed.
05, 06).
3. When finished, the keypad will display a "Bypass" message along
with each bypassed zone number, accompanied by a beep for each.
Wait for these zones to be displayed, to confirm their bypass.
All bypasses are removed
when an OFF sequence
(security code plus OFF)
is performed.
4. Arm the system as usual.
Bypassed zones are unprotected and will not cause an alarm if
violated while your system is armed.
B
D
A
C
AC
THESE KEYS
NOT PRESENT
ON ALL
06
BYPASS
{
READY
KEYPADS
TO BYPASS ZONES:
• ENTER CODE
• PRESS BYPASS KEY
• ENTER ZONE Nos.
STAY
OFF
AWAY
2
1
3
BYPASS
6
TEST
MAXIMUM
4
5
WAIT FOR
BYPASSED
ZONES TO BE
DISPLAYED
BEFORE ARMING
CODE
INSTANT
7
CHIME
8
9
READY
TYPICAL KEYPAD
#
0
*
Ð14Ð
BYPASSING PROTECTION ZONES
Quick Bypass If your system supports "Quick Bypass", it allows you to automatically
bypass all open (faulted) zones without having to enter zone numbers in-
dividually.
Ask your installer if
"Quick Bypass" is
active for your
system, and if so,
To use this feature, enter your security code, press the BYPASS key,
then stop. In a few moments, all open zones will be displayed along with a
"Bypass" message. Wait for all bypassed zones to be displayed, then
arm the system as usual.
check here:
AC
THE
SYSTEM
CAN
NOW BE ARMED WITH
ZONES BYPASSED
BYPASS
READY
Ð15Ð
ARMING PERIMETER ONLY
WITH ENTRY DELAY ON
Using the Use this key when you are staying inside, but expect someone to
use an entry/exit door later.
1. Enter your security code and press the STAY key.
3
STAY Key
2. The keypad beeps three times and displays the armed message. The
red ARMED indicator lights.
BEFORE ARMING
close all doors and windows
(see CHECKING FOR OPEN
ZONES on page 13).
3. The system arms. An alarm sounds immediately if a protected perimeter
window or non-entry/exit door is then opened, but you may otherwise
move freely throughout the premises.
Later arrivals can enter through an entry/exit door without causing
an alarm, but they must disarm the system within the entry delay
period to avoid sounding an alarm.
TYPICAL “ARMED STAY” DISPLAY
AC
B
D
A
C
THESE KEYS
NOT PRESENT
ON ALL
{
KEYPADS
STAY
STAY
OFF
AWAY
2
1
3
BYPASS
6
THE STAY KEY
ARMS THE
TEST
MAXIMUM
4
5
PERIMETER, BUT
ALLOWS USE OF
THE MAIN DOOR
CODE
INSTANT
7
CHIME
8
9
READY
TYPICAL KEYPAD
#
0
*
Ð16Ð
ARMING PERIMETER ONLY
WITH ENTRY DELAY OFF
Using the Use this key when you are staying inside and do not expect
anyone to use an entry/exit door.
1. Enter your security code and press the INSTANT key.
7
INSTANT Key
2. The keypad beeps three times and displays the armed message. The
red ARMED indicator lights.
BEFORE ARMING
close all doors and windows
(see CHECKING FOR OPEN
ZONES on page 13).
3. The system arms. An alarm sounds immediately if any protected
perimeter door or window is then opened, but you may otherwise move
freely throughout the premises.
An alarm sounds immediately if anyone opens an entry/exit door.
B
D
A
C
THESE KEYS
NOT PRESENT
ON ALL
TYPICAL “ARMED INSTANT” DISPLAY
AC
{
KEYPADS
STAY
OFF
AWAY
STAY
2
1
3
BYPASS
6
THE INSTANT
KEY ARMS THE
PERIMETER
(INCLUDING THE
MAIN DOOR),
WITH NO ENTRY
TEST
MAXIMUM
4
INSTANT
5
CODE
INSTANT
7
CHIME
8
9
READY
TYPICAL KEYPAD
#
0
*
Ð17Ð
ARMING ALL PROTECTION
WITH ENTRY DELAY ON
Using the Use this key when no one will be staying inside.
AWAY Key 1. Enter your security code and press the AWAY key.
2
2. The keypad beeps twice and displays the armed message. The red
ARMED indicator lights.
BEFORE ARMING
close all doors and windows
(see CHECKING FOR OPEN
ZONES on page 13).
3. You may leave through an entry/exit door during the exit delay period
without causing an alarm.
After exit delay, the system arms and sounds an alarm if a protected
window or non-entry/exit door is then opened, or if any movement is
detected inside your premises.
You may reenter through an entry/exit door, but must disarm the
system within the entry delay period to avoid an alarm.
B
D
A
C
THESE KEYS
NOT PRESENT
ON ALL
TYPICAL “ARMED AWAY” DISPLAY
{
AC
AWAY
KEYPADS
THE AWAY KEY
ARMS THE
STAY
OFF
AWAY
2
1
3
BYPASS
6
ENTIRE SYSTEM
(INTERIOR AND
PERIMETER), BUT
ALLOWS USE OF
THE MAIN DOOR
TEST
MAXIMUM
4
5
CODE
INSTANT
7
CHIME
8
9
READY
TYPICAL KEYPAD
#
0
*
Ð18Ð
ARMING ALL PROTECTION
WITH ENTRY DELAY OFF
Using the Use this key when the premises will be vacant for extended
periods of time such as vacations, etc., or when retiring for the night and
no one will be moving through protected interior areas.
4
MAXIMUM Key
1. Enter your security code and press the MAXIMUM key.
2. The keypad beeps twice and displays the armed message. The red
ARMED indicator lights.
BEFORE ARMING
close all doors and windows
(see CHECKING FOR OPEN
ZONES on page 13).
3. You may leave through an entry/exit door during the exit delay period
without causing an alarm.
After exit delay, the system arms and sounds an alarm immediately if
any protected door or window is opened, or if any movement is
detected inside your premises.
An alarm sounds immediately, when someone reenters.
B
D
TYPICAL “ARMED MAXIMUM” DISPLAY
A
C
THESE KEYS
NOT PRESENT
ON ALL
{
AC
AWAY
KEYPADS
STAY
OFF
AWAY
THE MAXIMUM
KEY ARMS THE
ENTIRE SYSTEM
(INCLUDING THE
MAIN DOOR),
WITH NO ENTRY
DELAY
2
1
3
BYPASS
6
INSTANT
TEST
MAXIMUM
4
5
CODE
INSTANT
7
CHIME
8
9
READY
TYPICAL KEYPAD
#
0
*
Ð19Ð
DISARMING THE SYSTEM AND SILENCING
ALARMS
Using the The OFF key is used to disarm the system and to silence alarm and
trouble sounds.
To Disarm the System
1
OFF Key
IMPORTANT:
If you return and the
main burglary sounder
is on:
Enter your security code and press the OFF key. The "Ready" message
will be displayed, and the keypad will emit a single tone to confirm that the
system is disarmed.
DO NOT ENTER, but
CONTACT THE POLICE
from a nearby safe location.
To Silence a Burglary Alarm
SEE IMPORTANT NOTE AT LEFT!
If you return after an
alarm has occurred and
the main sounder
has shut itself off:
the keypad will beep rapidly
Enter your security code and press the OFF key to silence the alarm (or
warning tones of a Memory of Alarm). Note the zone in alarm on the
keypad display, and make that zone intact (close door, window, etc.). Now
enter the security code plus OFF sequence again to clear the keypad's
upon your entering, indicating Memory of Alarm display. If the display will not clear and does not provide
that an alarm has occurred
during your absence
(the Memory of Alarm feature).
LEAVE IMMEDIATELY, and
CONTACT THE POLICE
from a nearby safe location.
a "Ready" message, notify the alarm agency.
To Silence a Fire Alarm simply press the OFF key (the security code is not
needed to silence FIRE alarms). To then clear the keypad's Memory of
Alarm display, enter your security code and press the OFF key.
See page 29 for additional fire alarm information.
WHEN SAFE TO DO SO,
re-enter
and follow the procedure
for silencing an alarm.
See the SUMMARY OF AUDIBLE/VISUAL NOTIFICATION section
for information which will help you to distinguish between FIRE
(Interrupted/Pulsed) and BURGLARY (Continuous/Steady) alarm
sounds.
Ð20Ð
USING THE KEYSWITCH
General Your system may be equipped with a keyswitch for use when arming and
disarming. A single red light on the keyswitch plate indicates the status of
your system as follows:
OFF = Disarmed, Not Ready for Arming
SLOW FLASHING = Disarmed, Ready for Arming
RAPID FLASHING = Armed STAY or AWAY
Arming To arm in the AWAY mode, turn key to right for 1/2 second.
To arm in the STAY mode, hold key turned to right for more than one
second.
The keypads will beep twice (AWAY mode) or 3 times (STAY mode) and
the keyswitch light will flash rapidly.
Disarming To disarm the system turn the key to the right and release.
If an alarm has occurred during the armed period, the keyswitch's light will
not flash on disarming (thus indicating memory of an alarm). Turning the
keyswitch key to the right a second time after disarming can clear the alarm
from memory, but it is advisable, instead, to refer to a keypad to diagnose
and clear any problem, and to subsequently clear alarm memory. See the
previous page for more about alarm memory.
Ð21Ð
CHIME MODE
Using the Your system can be set to alert you to the opening of a door or window
while it is disarmed by using CHIME mode. When activated, three tones
will sound at the keypad whenever a protected door or window is opened.
9
CHIME Key
Pressing the READY key will display the open points.
To turn Chime Mode on, enter the security code and press the CHIME
key. The CHIME message will appear.
To turn Chime Mode off, enter the security code and press the CHIME
key again. The CHIME message will disappear.
This feature can be used
only while the burglary
system is disarmed.
PANIC KEYS
Your system may have been programmed to use special keys or combi-
nations of keys to manually activate emergency (panic) functions. The
functions that might be programmed are: Silent Emergency, Audible
Emergency, Personal Emergency, and Fire.
Using
Panic Keys
(for manually activating
silent and/or
A silent emergency will send a silent alarm signal to the central station,
but there will be no audible alarms or visual displays.
An audible emergency will sound a loud, steady alarm at your
audible alarms)
TO INITIATE A PANIC
FUNCTION AT ANY TIME keypad(s) and at any external sounders that may be connected (ALARM
OF DAY OR NIGHT:
plus a zone number would also be displayed).
Press an active lettered key A personal emergency alarm will send an emergency message to the
for at least two seconds.
central station (if connected) and will sound at keypad(s), but not at
external bells or sirens.
or
Press both keys of an active
pair at the same time.
A fire alarm will send a fire alarm message to the central station and will
uniquely sound at keypad(s) and external bells and sirens (FIRE plus a
zone number would also be displayed).
Ð22Ð
(continued)
PANIC KEYS
B
A
THESE KEYS
NOT PRESENT
ON ALL
INDIVIDUAL PANIC
KEYS (“D” NOT USED)
{ }
D
C
KEYPADS
STAY
OFF
AWAY
2
1
3
BYPASS
6
TEST
MAXIMUM
4
5
CODE
INSTANT
7
CHIME
3
#
#
&
&
&
PAIRED
PANIC
KEYS
8
9
✱
1
READY
}
#
0
✱
*
CHECK IF
ACTIVE
PANIC
KEY(S)
P R O G R A M M E D
F U N C T I O N
ZONE
NUMBER
[A]
[B]
SILENT EMERGENCY (Fixed-Function)
95
07
96
____SILENT, ____AUDIBLE, ____PERSONAL, ____FIRE
AUDIBLE EMERGENCY (Fixed-Function)
SEE YOUR INSTALLER
[C]
AND NOTE HERE
OR
THE KEY(S) & FUNCTION(S)
[1] & [✴]
[✴] & [#]
[3] & [#]
SILENT EMERGENCY (Fixed-Function)
____SILENT, ____AUDIBLE, ____PERSONAL, ____FIRE
AUDIBLE EMERGENCY (Fixed-Function)
95
07
96
PROGRAMMED
FOR YOUR SYSTEM
¥ KEYS [A], [B], AND [C] ARE NOT PRESENT ON ALL KEYPADS.
¥ KEY [D], IF PRESENT ON YOUR KEYPAD, IS NOT ACTIVE HERE.
Ð23Ð
TESTING THE SYSTEM
TO BE CONDUCTED WEEKLY
The TEST key puts your system into Test mode, which allows each pro-
tection point to be checked for proper operation.
Using the
TEST Key
5
1. Disarm the system and close all protected windows, doors, etc. The
keypad's READY message should be displayed and the READY
indicator (if present) should be lit.
NO ALARM REPORTS
WILL BE SENT TO THE
CENTRAL MONITORING
2. Enter your security code and press the TEST key.
STATION while the 3. The keypad will sound a single beep every 40 seconds as a reminder
system is in Test mode.
that the system is in the test mode.
Each time a protection zone is faulted, the external siren or bell should
sound for one second and then turn off, while the keypad sounds 3 beeps.
If this does not happen, call for service immediately.
4. Open and close each protected door and window in turn and listen for
the required sounds The identification of each faulted protection point
should appear on the display.
5. Walk in front of any interior motion detectors (if used) and listen for the
required sound as movement is detected. The identification of the
detector should appear on the display when it is activated.
Note: Wireless PIR (Passive Infrared) units will send signals out only if
they have been inactive for 3 minutes.
Ð24Ð
(continued)
TESTING THE SYSTEM
6. Follow the manufacturer's instructions to test all smoke detectors, to
ensure that all are functioning properly. The identification of each
detector should appear on the display when each is activated.
7. After all protection points have been checked and restored, there
should be no zone identification numbers displayed. If a problem is
experienced with any protection point (no confirming sounds,
no display), CALL FOR SERVICE IMMEDIATELY.
8. Turn off the Test mode by entering the security code and pressing the
OFF key.
Ð25Ð
TROUBLE CONDITIONS
"Check" and The word CHECK on the keypad's display, accompanied by a "beeping"
at the keypad, indicates a trouble condition in the system.
"Battery" Displays
To silence the beeping for these conditions, press any key.
1. A display of "CHECK" and one or more zone numbers indicates
that a problem exists with the displayed zone(s) and requires your
attention. If the CHECK display relates to a fire zone, CALL FOR
SERVICE IMMEDIATELY.
Determine if the zone(s) displayed are intact and make them so if they
are not. If the problem has been corrected, the display can be cleared if
you enter the OFF sequence (user code plus OFF key) twice. If the
display persists, CALL FOR SERVICE IMMEDIATELY.
2. If there are wireless sensors in your system, the CHECK
Not all systems use
wireless sensors.
condition may also be caused by some change in the environment that
prevents the receiver from hearing a particular sensor. CALL FOR
SERVICE IMMEDIATELY if this occurs.
Ð26Ð
(continued)
TROUBLE CONDITIONS
3. A display of "BAT" with no zone number or beeping indicates that
the main standby battery in your control is weak. If this condition
persists for more than one day (with AC present), CALL FOR
SERVICE.
4. A display of "BAT" with a zone number and a once per 40
seconds "beeping" at the keypad indicates that a low battery
condition exists in the wireless sensor displayed. Either replace the
battery yourself, or CALL FOR SERVICE. If the battery is not
replaced within 30 days, a CHECK display may occur.
Power Failure If there is no keypad display at all, and the POWER indicator (if
present) is not lit, operating power for the system has stopped and the
system is inoperative. CALL FOR SERVICE IMMEDIATELY.
If the message "AC LOSS" or "NO AC" is displayed, and the
POWER indicator (if present) is off, the keypad is operating on
battery power only. If only some lights are out on the premises, check cir-
cuit breakers and fuses and reset or replace as necessary. CALL FOR
SERVICE IMMEDIATELY if AC power cannot be restored.
Ð27Ð
(continued)
TROUBLE CONDITIONS
Other Displays dl: If this remains displayed for more than 1 minute, your system is
disabled. CALL FOR SERVICE IMMEDIATELY.
CC: The system is in communication with the central station for change of
function or status verification. If this message persists for more
than 10 minutes, CALL YOUR SERVICE COMPANY.
FC: A communication failure has occurred. CALL FOR SERVICE
IMMEDIATELY.
OC The keypad is not receiving signals from the control panel and sees
an open circuit. If this message persists for more than 10 minutes,
CALL YOUR SERVICE COMPANY.
FOR SERVICING INFORMATION,
SEE PAGE 43
Ð28Ð
FIRE ALARM SYSTEM
IF INSTALLED
Your fire alarm system (if installed) is on 24 hours a day, for continuous
protection. In the event of an emergency, the strategically located smoke
and heat detectors will automatically send signals to your system, triggering
a loud, interrupted sound from the keypad. An interrupted sound will also
be produced by optional exterior sounders. A FIRE message will appear at
your keypad and remain on until you silence the alarm.
General
1. Should you become aware of a fire emergency before your detectors
sense the problem, go to your nearest keypad and manually initiate an
alarm by pressing the panic key pair assigned as FIRE emergency (if
programmed by the installer) as indicated on page 23.
In Case Of Fire Alarm
2. Evacuate all occupants from the premises.
3. If flames and/or smoke are present, leave the premises and notify your
local Fire Department immediately.
4. If no flames or smoke are apparent, investigate the cause of the alarm.
The zone number(s) of the zone(s) in an alarm condition will be
displayed at the keypad.
TYPICAL FIRE EMERGENCY DISPLAY
AC
05
READY
ALARM
FIRE
Ð29Ð
(continued)
FIRE ALARM SYSTEM
IF INSTALLED
Silencing Fire Alarms 1. Silence the alarm by pressing the OFF key (security code not needed
to silence fire alarms). To clear the display, enter your code and press
the OFF key again (Memory of Alarm).
2. If the keypad does not indicate a READY condition after the second
OFF sequence, press the READY key to display the zone(s) that are
faulted. Be sure to check that smoke detectors are not responding to
smoke or heat producing objects in their vicinity. Should this be the
case, eliminate the source of heat or smoke.
3. If this does not remedy the problem, there may still be smoke in the
detector. Clear it by fanning the detector for about 30 seconds.
4. When the problem has been corrected, clear the display by entering
your code and pressing the OFF key.
Ð30Ð
NATIONAL FIRE PROTECTION ASSOCIATION
RECOMMENDATIONS ON SMOKE DETECTORS
General
With regard to the number and placement of smoke/heat detectors, we subscribe to the
recommendations contained in the National Fire Protection Association's Standard #74 noted below.
Early warning fire detection is best
✪
▲
✪
✪
✪
✪
KITCHEN
▲
✪
achieved by the installation of fire
detection equipment in all rooms and
areas of the premises as follows: A
smoke detector installed outside of
each separate sleeping area, in the
immediate vicinity of the bedrooms and
on each additional story of the family
living unit, including basements and
excluding crawl spaces and unfinished
attics.
KITCHEN
BDRM
DINING
BEDROOM
BEDROOM
TV ROOM
DINING
■
BDRM
LIVING ROOM
■
✪
✪
✪
■
✪
BEDROOM
BEDROOM
LIVING ROOM
✪
▲
Smoke Detectors for Minimum Protection
Smoke Detectors for Additional Protection
Heat-Activated Detectors
■
✪
▲
■
In addition, it is recommended that the
owner consider the use of heat or
smoke detectors in the living room,
dining room, bedroom(s), kitchen,
hallway(s), attic, furnace room, utility
and storage rooms, basements and
attached garages.
BEDROOM
■
✪
BEDROOM
✪
BEDROOM
TO
BR
▲
■
▲
KTCHN
GARAGE
CLOSED
DOOR
LVNG RM
.
■
BASEMENT
Ð31Ð
EMERGENCY EVACUATION
Steps to Safety
Establish and regularly practice a plan of escape in the event of fire. The
following steps are recommended by the National Fire Protection
Association:
1. Plan on your detector or your interior and/or exterior sounders warning
all occupants.
CLOSET
BEDROOM
2. Determine two means of escape from each room. One path of es-
cape should lead to the door that permits normal exit from the building.
The other may be a window, should your path be unpassable.
Station an escape ladder at such windows if there is a long drop to
the ground.
TH
BA
BEDROOM
BEDROOM
2ND FLOOR
KITCHEN
BEDROOM
3. Sketch a floor plan of the building. Show windows, doors, stairs and
rooftops that can be used to escape. Indicate escape routes for each
room. Keep these routes free from obstruction and post copies of the
escape routes in every room.
BACK DOOR
TH
BA
BEDROOM
1ST FLOOR
4. Assure that all bedroom doors are shut while you are asleep. This
will prevent deadly smoke from entering while you escape.
5. Try the door. If the door is hot, check your alternate escape route. If
the door is cool, open it cautiously. Be prepared to slam the door if
smoke or heat rushes in.
•
•
6. In smoky areas, crawl close to floor, hold your breath, and/or cover
mouth and nose with a wet cloth.
7. Escape quickly; don't panic.
BACK
8. Establish a common meeting place outdoors, away from your
premises, where everyone can meet and then take steps to contact
the authorities and account for those missing. Choose someone to
assure that nobody returns to the premises Ñ many die going back.
•
FRONT
Ð32Ð
QUICK GUIDE TO ALARM SYSTEM FUNCTIONS
FUNCTION
Check Zones
Arm System
PROCEDURE
COMMENTS
Press READY key.
To view faulted zones when system not ready.
Arms system in mode selected.
Enter code. Press arming key desired:
(AWAY, STAY, INSTANT, MAXIMUM)
Quick Arm
(if programmed)
Press #. Press arming key desired:
(AWAY, STAY, INSTANT, MAXIMUM)
Arms system in mode selected, quickly and without use of code.
Bypass Zone(s)
Enter code. Press BYPASS key.
Enter zone number(s) to be bypassed
(use 2-digit entries).
Bypassed zones are unprotected and will not cause an alarm if violated.
Quick Bypass
Enter code. Press BYPASS key.
Bypasses all faulted zones automatically.
(if programmed)
Silence Sounders
Burglary:
Fire:
Enter code. Press OFF key.
Press OFF key.
Press any key.
Also disarms system. Memory of alarm remains until cleared.
Memory of Alarm remains until cleared.
Determine cause. See Page 26.
"Check":
Disarm System
Enter code. Press OFF key.
Also silences sounders. Memory of alarm remains until cleared.
Clear Alarm
Memory
After disarming, enter code again.
Press OFF key again.
Keypad will beep rapidly upon entry if alarm has occurred.
Alarm display will remain upon disarming until cleared.
Duress
Enter user code 8 to arm or disarm "normally."
Performs desired action and sends silent alarm to central station.
(if connected to
central station)
Panic Alarms
(as programmed)
Press key [A], [B], or [C] for at least 2 sec., or
(if no A, B, or C on your keypad)
press keys [1]&[✴], or [✴]&[#], or [3]&[#],
both at same time.
See Page 23 for functions programmed for your system.
Chime Mode
Test Mode
To turn ON or OFF: Enter code. Press CHIME
key.
Keypad will sound if doors or windows are violated while system is
disarmed and chime mode is ON.
To turn ON: Enter code. Press TEST key.
To turn OFF: Enter code. Press OFF key.
Tests alarm sounder and allows sensors to be tested.
Ð33Ð
SUMMARY OF AUDIBLE/VISUAL NOTIFICATIONS
SOUND
CAUSE
DISPLAY
LOUD, INTERRUPTED
Keypad & External
FIRE ALARM
FIRE and ALARM are displayed; protection zone in alarm is displayed.
LOUD, CONTINUOUS
Keypad & External
BURGLARY/AUDIBLE
EMERGENCY ALARM
a. SYSTEM DISARM
ALARM is displayed; protection zone in alarm is also displayed.
ONE SHORT BEEP
(not repeated)
Keypad only
a. Only READY is displayed. Green READY indicator (if present) is lit.
b. SYSTEM ARMING ATTEMPT b. NOT READY is displayed, open protection zone number is displayed.
WITH AN OPEN ZONE
Green READY indicator (if present) is not lit.
c. BYPASS VERIFY
c. The bypassed protection zone numbers are displayed. (One beep for each number
displayed.) BYPASS also displayed.
ONE SHORT BEEP
(once every 40 seconds)
Keypad only
SYSTEM IS IN TEST MODE
Opened Zone identifications will appear.
ONE BEEP every 40 sec.
Keypad only
a. LOW BATTERY AT XMTR
b. TROUBLE
a. BAT displayed with ID number of transmitter.
b. CHECK displayed. Troubled protection zone is displayed.
AWAY and (if MAXIMUM) INSTANT are displayed.
TWO SHORT BEEPS
Keypad only
ARM AWAY OR MAXIMUM
THREE SHORT BEEPS
Keypad only
a. ARM STAY OR INSTANT
a. STAY and (if INSTANT) INSTANT are displayed. Red ARMED indicator is lit.
b. ZONE OPENED WHILE SYS- b. CHIME displayed. Pressing ✴/ READY key will display opened zone.
TEM IS IN CHIME MODE
c. ZONE OPENED WHILE SYS-
TEM IS IN TEST MODE
c. Open protection zone number is displayed.
RAPID BEEPING
Keypad only
MEMORY OF ALARM
FIRE and/or ALARM is displayed; zone in alarm is displayed.
SLOW BEEPING
Keypad only
ENTRY DELAY WARNING
None during delay; Exceeding the delay time without disarming causes alarm.
If bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady ring.
Notes: ¥ BAT displayed (with no beeping or zone number) indicates system main battery is weak (see page 27).
¥ Also see Power Failure, and Other Displays under TROUBLE CONDITIONS on page 27.
Ð34Ð
PROTECTION ZONES LIST
One or more sensing devices will have been assigned by the installer of your alarm system to each of the various
protection zones in your system (although not every zone number can be used). For example, the sensing device
on your Entry/Exit door may have been assigned to zone 06, sensing devices on windows in the master bedroom
to zone 10, and so on.
Zone numbers 07, 95 and 96 represent keypad "Panic" alarm functions assigned by the installer (see Page 23).
Zone numbers 08 and 09 are reserved for Duress and Tamper signal reporting to the central station.
This chart may be used to record the specific zone number assignments for your system. Your installer will assist
you in recording this information.
PROTECTION ZONE DESCRIPTIONS
Zone Description
Zone Description
Zone Description
Zone Description
01
02
03
04
05
06
17
18
19
20
21
22
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
07 Key B (or: ✴ & #) Panic 23
24
57
58
08
09
10
11
12
13
14
15
16
ÐDuressÐ
ÐTamperÐ
25
26
27
28
29
30
31
32
33
59
60
61
62
63
95 Key A (or 1 & ✴) Panic
96 Key C (or 3 & #) Panic
Ð35Ð
Ð NOTES Ð
Ð36Ð
OWNER'S INSURANCE PREMIUM
CREDIT REQUEST
This form should be completed and forwarded to your homeowner's insurance carrier for possible premium credit.
A . GENERAL INFORMATION:
Insured's Name and Address: _________________________________________________________________
__________________________________________________________________
Insurance Company: _________________________________ Policy No.: _____________________________
First Alert System: FA120C
Type of Alarm:
Burglary
Fire
Both
Installed by: _________________________________ Serviced by: ___________________________________
name
name
________________________________
address
___________________________________
address
B . NOTIFIES (Insert B for Burglary, F for Fire, where appropriate):
Local Sounding Device________ Police Dept.________ Fire Dept. _______
Central Station ________
Name and Address: _________________________________________________________________________
C . POWERED BY: A.C. With Rechargeable Power Supply
D . TESTING:
Quarterly,
Monthly,
Weekly,
Other_________________________________
continued on other side
Ð37Ð
OWNER'S INSURANCE PREMIUM
CREDIT REQUEST (cont.)
E . SMOKE DETECTOR LOCATIONS:
Furnace Room
Basement
Kitchen
Bedrooms
Attic
Hall
Living Room
Dining Room
F . BURGLARY DETECTING DEVICE LOCATIONS:
Front Door
Basement Door
All windows
Rear Door
All Exterior Doors
1st Floor Windows
Interior Locations
All Accessible Openings, Including Skylights, Air Conditioners and Vents
G . ADDITIONAL PERTINENT INFORMATION:
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
Signature: __________________________________________________ Date: _______________________
Ð38Ð
CANADIAN DEPARTMENT OF COMMUNICATIONS (DOC) STATEMENT
NOTICE
AVIS
The Canadian Department of Communications label identifies
certified equipment. This certification means that the equip-
ment meets certain telecommunications network protective,
operational and safety requirements. The Department does
not guarantee the equipment will operate to the user's satis-
faction.
L'Žtiquette du minist•re des Communications du Canada identifie le
matŽriel homologuŽ. Cette Žtiquette certifie que le matŽriel est conforme
ˆ certaines normes de protection, d'exploitation et de sŽcuritŽ des rŽseaux
de tŽlŽcommunications. Le minist•re n'assure toutefois pas que le
matŽriel fonctionnera ˆ la satisfaction de l'utilisateur.
Avant d'installer ce matŽriel, l'utilisateur doit s'assurer qu'il est permis de
le raccorder aux installations de l'entreprise locale de tŽlŽcommuni-
cations. Le matŽriel doit Žgalement •tre installŽ en suivant une mŽthode
acceptŽe de raccordement. Dans certains cas, les fils intŽrieurs de l'en-
treprise utilisŽs pour un service individuel ˆ la ligne unique peuvent •tre
prolongŽs au moyen d'un dispositif homologuŽ de raccordement (cordon
prolongateur tŽlŽphonique interne). L'abonne ne doit pas oublier qu'il est
possible que la conformitŽ aux conditions ŽnoncŽes ci-dessus n'emp•che
pas la dŽgradation du service dans certaines situations. Actuellement, les
entreprises de tŽlŽcommunications ne permettent pas que l'on raccorde
leur matŽriel aux prises d'abonnŽs, sauf dans les cas precis prŽvus par
les tarifs particuliers de ces entreprises.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be
installed using an acceptable method of connection. In some
cases, the company's inside wiring associated with a single
line individual service may be extended by means of certified
connector assembly (telephone extension cord). The cus-
tomer should be aware that compliance with the above condi-
tions may not prevent degradation of service in some situa-
tions.
Repairs to certified equipment should be made by an autho-
rized Canadian maintenance facility designated by the sup-
plier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to
disconnect the equipment.
Les rŽparations du matŽriel homologuŽ doivent •tre effectuŽes pas un
centre d'entretien canadien autorisŽ dŽsignŽ par le fournisseur. La
compagnie de tŽlŽcommunications peut demander ˆ l'utilisateur de
dŽbrancher un appareil ˆ la suite de rŽparations ou de modifications effec-
tuŽes par l'utilisateur ou ˆ cause de mauvais fonctionnement.
Users should ensure for their own protection that the electri-
cal ground connections of the power utility, telephone lines
and internal metallic water pipe system, if present, are con-
nected together. This precaution may be particularly impor-
tant in rural areas.
Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de
mise en terre de la source d'Žnergie Žlectrique, des lignes tŽlŽphoniques
de rŽseau de conduites d'eau, s'il y en a, soient raccordŽs ensemble.
Cette prŽcaution est particuli•rement importante dans les rŽgions rurales.
Avertissement: L'utilisateur ne doit pas tenter de faire ces
raccordements lui-m•me; il doit avoir recours ˆ un service d'inspection
des installations Žlectriques, ou ˆ un Žlectricien, selon le cas.
Caution: User should not attempt to make such connections
themselves, but should contact the appropriate electric
inspection authority, or electrician, as appropriate.
L'indice de charge (IC) assignŽ ˆ chaque dispositif terminal pour Žviter
toute surcharge indique le pourcentage de la charge totale qui peut •tre
raccordŽ ˆ un circuit tŽlŽphonique fermŽ utilisŽ par ce dispositif. La
terminaison du circuit fermŽ peut •tre constituŽe de n'importe quelle
combinaison de dispositifs, pourvu que la somme des indices de charge
de l'ensemble des dispositifs ne dŽpasse pas 100.
The Load Number (LN) assigned to each terminal device de-
notes the percentage of the total load to be connected to a
telephone loop which is used by the device, to prevent over-
loading. The termination on a loop may consist of any combi-
nation of devices subject only to the requirement that the total
of the Load Numbers of all the devices does not exceed 100.
Ð39Ð
UL NOTICE: This is a "Grade A" Residential System.
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following
statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance
with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and
found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules,
which are designed to provide reasonable protection against such interference in a residential installation. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
¥ If using an indoor antenna, have a quality outdoor antenna installed.
¥ Reorient the receiving antenna until interference is reduced or eliminated.
¥ Move the radio or television receiver away from the receiver/control.
¥ Move the antenna leads away from any wire runs to the receiver/control.
¥ Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The
user or installer may find the following booklet prepared by the Federal Communications Commission helpful:
"Interference Handbook"
This booklet is available from the U.S. Government Printing Office, Washington, DC 20402.
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or
User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 STATEMENT
This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains, among
other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this in-
formation must be provided to the telephone company.
This equipment uses the following jacks:
An RJ31X is used to connect this equipment to the telephone network.
The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the
telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the
RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by
the total RENs, contact the telephone company to determine the maximum REN for the calling area.
(continued)
Ð40Ð
(continued) FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 STATEMENT
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary dis-
continuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as
soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the opera-
tion of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the neces-
sary modifications in order to maintain uninterrupted service.
If trouble is experienced with this equipment, please contact the manufacturer for repair and warranty information. If the trou-
ble is causing harm to the telephone network, the telephone company may request you remove the equipment from the net-
work until the problem is resolved.
There are no user serviceable components in this product, and all necessary repairs must be made by the manufacturer.
Other repair methods may invalidate the FCC registration on this product.
This equipment cannot be used on telephone company-provided coin service. Connection to Party Line Service is subject to
state tariffs.
This equipment is hearing-aid compatible.
When programming or making test calls to an emergency number, briefly explain to the dispatcher the reason for the call. Per-
form such activities in the off-peak hours; such as early morning or late evening.
IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS
If your security system has been connected to the telephone line, and there is trouble with regular telephone service,
disconnect the security system from the telephone line by removing the plug from the RJ31X (CA38A in Canada) telephone
wall jack (you should have been shown how to do this by your installing company). Do not attempt to disconnect the telephone
line connection inside the control cabinet. Doing so will result in the COMPLETE disruption of your regular telephone service.
If the regular phone works correctly after the plug has been disconnected from the RJ31X wall jack, the security system has a
problem and you should call your service representative for service immediately. If, upon disconnection of the security
system from the wall jack, there is still a problem with telephone service, notify the telephone company that they have a
problem and request prompt repair service.
IMPORTANT: A security system connected to an alarm monitoring station relies on that connection.
¥ If the security system is at fault, reinsert the plug as soon as the security system is repaired.
¥ If the phone service is at fault, re-insert the plug immediately, to ensure resumption of full protection upon
restoration of phone service.
The user may not, under any circumstances (in or out of warranty), attempt any service or repairs to the system.
Ð41Ð
WARNING!
THE LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or
other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a
variety of reasons. For example:
¥ Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm
sensor or disconnect an alarm warning device.
¥ Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work
without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put
in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly.
¥ Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if
the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the
path.
¥ A user may not be able to reach a panic or emergency button quickly enough.
¥ While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not acti-
vate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the
Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System
may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may
not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the
other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A
second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors have
sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always
warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas,
improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson.
Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as
anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death.
¥ Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their
installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams
of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect
motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or
windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the
optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however,
as the ambient temperature of protected area approaches the temperature range of 90° to 105°F (32° to 40°C), the
detection performance can decrease.
(continued)
Ð42Ð
(continued) WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM
¥ Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the
other side of closed or partly open doors. If warning devices sound on a different level of the residence from the
bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not
hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic.
Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers.
¥ Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or
temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.
¥ Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect
themselves from the situation. In the case of a monitored alarm system, authorities may not respond appropriately.
¥ This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to
last as long as 10 years, the electronic components could fail at any time.
The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance.
This alarm system should be tested weekly to make sure all sensors and transmitters are working properly.
Wireless transmitters (used with some systems) are designed to provide long battery life under normal operating
conditions. Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific
wireless device being used. External factors such as humidity, high or low temperatures, as well as large swings in
temperature, may all reduce the actual battery life in a given installation. This wireless system, however, can identify a true
low battery situation, thus allowing time to arrange a change of battery to maintain protection for that given point within the
system.
Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insur-
ance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to
insure their lives and property.
We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved
ones to learn about these developments.
SERVICING INFORMATION
Your local authorized service representative is the person best qualified to service your alarm system.
Arranging a regular program with that person is advisable. Your local service representative is:
NAME: ____________________________________________ PHONE: __________________________
ADDRESS: ______________________________________________________________________________
______________________________________________________________________________
Ð43Ð
ONE YEAR LIMITED WARRANTY
Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"), 165 Eileen Way, Syosset, New York 11791,
warrants its First Alert security equipment (the "product") to be free from defects in materials and workmanship for one year
from date of original purchase, under normal use and service. Seller's obligation is limited to repairing or replacing, at its
option, free of charge for parts, labor, or transportation, any product proven to be defective in materials or workmanship under
normal use and service. Seller shall have no obligation under this warranty or otherwise if the product is altered or improperly
repaired or serviced by anyone other than the Seller. In case of defect, contact the security professional who installed and
maintains your security equipment or the Seller for product repair.
This one year Limited Warranty is in lieu of all other express warranties, obligations or liabilities. THERE ARE NO EXPRESS
WARRANTIES, WHICH EXTEND BEYOND THE FACE HEREOF. ANY IMPLIED WARRANTIES, OBLIGATIONS OR
LIABILITIES MADE BY SELLER IN CONNECTION WITH THIS PRODUCT, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, ARE LIMITED IN DURATION TO A
PERIOD OF ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. ANY ACTION FOR BREACH OF ANY WARRANTY, IN-
CLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY, MUST BE BROUGHT WITHIN 12
MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR
IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY
THE SELLER'S OWN NEGLIGENCE OR FAULT. Some states do not allow limitation on how long an implied warranty lasts or
the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Seller does not represent that the product may not be compromised or circumvented; that the product will prevent any
personal injury or property loss by burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate
warning or protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of a burglary,
robbery, fire or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur
or that there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY
FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO
GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR
DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S
MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE
COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. No increase or alteration, written or verbal, to this warranty is authorized.
172 Michael Drive
Syosset, New York 11791
COPYRIGHT © 1996 PITTWAY CORPORATION
N5100-3V3 9/96
|