GE Monogram Ventilation Hood ZXR8510 User Manual

Installation

Instructions

If you have questions, call 800.GE.CARES or visit our website at: www.monogram.com

ZXR858, ZXR859 and ZXR8510

Recirculating Accessories

For Model ZV850, Island Vent Hood

Installation Preparation

REQUIRED ACCESSORIES

• Order the required accessory at the same time as the

vent hood and have on site before installation.

• Each kit includes decorative duct covers, a support

frame, air deflector and charcoal filters.

This book provides step by step instructions to install

the Monogram ZV850 ceiling mounted hood for

recirculating operation.

• One of the following accessory kits is required for non-

vented ceiling mounted installations of model ZV850.

Choose the correct kit according to ceiling heights:

ZXR858 – For 8 ft. ceiling height.

ZXR859 – For 9 ft. ceiling height

ZXR8510 – For 10 ft. ceiling height.

PRODUCT DIMENSIONS

The vent hood must be installed 24″ min. and 30″ max.

above the cooking surface. 25-1/2″ is recommended for

best performance and to ensure that the duct cover

meets the ceiling. The cooking surface should be at least

36″ above the floor. Installation will be easier if the vent

hood is installed before the cooktop and countertop is

installed.

*Height

to Ceiling

8-1/4"

35-3/8"

27-1/2"

* 26-1/4” for 8 ft. Ceiling

Using ZXR858 Accessory

38-1/8” for 9 ft. Ceiling

Using ZXR859 Accessory

50-1/8” for 10 ft. Ceiling

Using ZXR8510 Accessory

*25-1/2" Recommended

* The distance between the cooking surface and the bottom of the

hood must be at least 24” and up to 30”. The 25-1/2” recommended

installation height, above the standard 36” countertop, will ensure

duct cover fit to the ceiling.

36" Reference

Installation Preparation

USING DUCT COVER ACCESSORIES

POWER SUPPLY

A duct cover accessory is required for all ceiling

heights. Use this chart to determine the correct Duct

Cover Accessory for 8-ft. to 10-ft. ceilings that must be

ordered with the hood.

IMPORTANT

- (Please read carefully)

WARNING:

FOR PERSONAL SAFETY, THIS APPLIANCE MUST

BE PROPERLY GROUNDED.

ZV850SB Installation Heights

Actual

Remove house fuse or open circuit breaker before

beginning installation.

*Possible Hood

Installation Height

Ceiling

Height

Recirculating

Accessory

24-1/2″

Do not use an extension cord or adapter plug with

this appliance. Follow National electrical codes or

prevailing local codes and ordinances.

7′ 11″

Electrical supply

25-1/2″

8′ 0″

This vent hood must be supplied with 120V, 60Hz,

and connected to an individual, properly grounded

branch circuit, and protected by a 15 or 20 amp

circuit breaker or time delay fuse.

• Wiring must be 2 wire with ground.

• If the electrical supply does not meet the above

requirements, call a licensed electrician before

proceeding.

• Route house wiring in the ceiling, as close to the

installation location as possible. Allow an addi-

tional 3 feet length from ceiling joists to reach the

junction box on the hood.

25-1/2″ to 26-1/2″

25-1/2″ to 27-1/2″

25-1/2″ to 28-1/2″

25-1/2″ to 29-1/2″

30″ max.

8′ 1″

8′ 2″

8′ 3″

8′ 4″

8′ 5″

8′ 6″

8′ 7″

8′ 8″

8′ 9″

8′ 10″

8′ 11″

9′ 0″

9′ 1″

9′ 2″

9′ 3″

9′ 4″

9′ 5″

9′ 6″

9′ 7″

9′ 8″

9′ 9″

9′ 10″

9′ 11″

10′ 0″

30″ max.

• Connect the wiring to the house wiring in accor-

dance with local codes.

Grounding instructions

The grounding conductor must be connected to a

ground metal, permanent wiring system, or an

equipment-grounding terminal or lead on the hood.

30″ max.

WARNING:

The improper connection of

the equipment-grounding conductor can result in a

risk of electric shock. Check with a qualified electri-

cian or service representative if you are in doubt

whether the appliance is properly grounded.

TOOLS AND MATERIALS

REQUIRED ^{(NOT SUPPLIED)}

• Tape measure

• Knife

• Spirit level

• 10 mm Hex wrench/socket

• Safety glasses

• Duct tape

*Based on 36″ countertop height.

• Wire cutter/stripper

• Wire nuts

• Electric drill and 5/32” bit

• Phillips and flat-blade

screwdrivers

• Hammer

• Pliers

• Plumb

9-7/16"

ZV850SB Duct Cover Dimensions

• Gloves to protect against sharp

edges

• 120V 60Hz. 15 or 20 Amp, 2 wire

with ground. Properly grounded

branch circuit.

• Strain relief for junction cover

• 6” round duct, length to suit

installation

Recirculating

Installation

15″

22-1/2″

27-15/16″

14-3/16″

21-7/8″

26″

ZXR858C

ZXR859C

ZXR8510C

• Center punch

15-3/4"

Installation Preparation

Check contents of the required accessory,

ZXR858, ZXR859 or ZXR8510.

REMOVE THE PACKAGING

The vent hood is packed separate from the required

accessory: ZXR858, ZXR859 or ZXR8510.

• Remove the frame, cover, parts box, side bars and

packaging.

Mounting Screw Holes

• Remove junction box cover.

• Install strain relief onto junction box cover.

Check Installation Hardw are

Locate the hardware accessory box packed with the

hood and check contents.

Support Frames

With 8 Screws

And 8 Washers

Decorative Duct Covers

4 Flat Washers

2 Phillips Head

Decorative Screws

8 Frame Attachment

Screws with Washers

(attached to

accessory

support frames)

4 Hex head

wood lag screws

(6mm x 2-1/2”

3 Charcoal Filters

1/4 x 2-1/2")

Front of Hood

PLAN THE LOCATION

Determine the exact location of the vent hood.

• Use a plumb to check location to be sure countertop/

cooktop location below the hood will align exactly.

Template

4 (10mm) Nuts

and Lock Washers

• The hood should project forward 1-1/2 beyond the front

″

edge of the cooking appliance. See illustration.

• Observe the recommended space between the cooking

surface and bottom of hood.

Check service manual

envelope taped to the front

on the hood to be sure it

contains one stop screw.

Leave this screw in the

envelope.

Ceiling

Hood

Ducting

Centerline

Hood

3 Stainless Steel

Grease Filters

Front

13-3/4"

27-1/2"

Approx. 1-1/2"

Beyond Cooking

Surface

Cooktop

2 side bars with 4 Machine screws

Countertop

Side View

Installation Preparation

• The cross framing must be level in all directions.

Check with a spirit level and adjust if necessary.

INSTALL CEILING

SUPPORT STRUCTURE

• At the hood location, install 2 x 4 cross framing

between ceiling joists as shown.

Cross Framing

• The 2 x 4 cross framing can be installed standing or

flat. See illustration.

Top View of Support Framing

8-3/4"

Cross

Framing

8-3/4"

Ceiling

Joist

7-5/8"

Support

Frame

Opening

16"

Joist

*7-5/8"

Upper Half

Of Support

Frame

Front

Hood

Typical Support Frame Mounting

Height

Adjustment

Slot

– The framing should be spaced 8-5/8” on the sides and 7-5/8”

at the front from centerline to centerline to accept mounting

screws in the vent support frame.

IMPORTANT: The ceiling structure must be capable of supporting

the weight of the hood (approximately 100 pounds) and any

inadvertent user contact loads. It is recommended that the hood

support frame be supported by a minimum of 2 x 4 cross framing.

Cross

Framing

Ceiling

Finish the Ceiling

Once the ceiling is finished, mark the location of the

ceiling joist and cross framing.

• Check to be sure that ceiling is level, use shims if

necessary.

8-3/4"

Front of

Hood

MOUNT TEMPLATE

• Align the template with the marks on the ceiling

Side

View

and tape in place.

Support

Frame

– Be sure the template is oriented correctly, with the

front of the hood.

• Use a plumb to be sure the mounting holes will

provide parallel alignment with the countertop

below.

Note: The cross framing must be spaced 8-3/4" on the side from

centerline to centerline in order to accept the hood mounting

screws.

• Center punch all hole

locations.

• Drill pilot holes in the 4 screw

locations. Use a 5/32″ bit and

drill approximately 1-1/2″

deep.

• Cut wire access hole

approximately 1″ dia.

• Arrange cross framing in the ceiling to suit the

existing structure. See examples.

– Secure each 2 x 4 block with at least four (4), #10

wood screws, 3″ long (minimum size screws, not

supplied). Use 8 wood screws total for the two

supports.

Front of Hood

• The cross framing must be accurately aligned to

assure correct positioning of the hood.

Wire Access Hole

Installation Instructions

INSTALL UPPER SUPPORT FRAME

INSTALL LOWER SUPPORT FRAME

• Install the plastic upper duct connector to the

upper support frame by inserting from the bottom

and snapping into the opening of the air deflector

(already installed).

• Secure the upper support frame to the ceiling joists

and/or cross framing with the 4 screws provided.

For maximum rigidity and strength, the screws must

be driven into the center of the joists and/or cross

framing.

• Insert lower support frame (from required accessory

ZXR858, ZXR859 or ZXR8510) into the upper

support frame and loosely secure with 8 screws and

washers (4 on the front and 4 on the back sides).

• Adjust the lower support frame up or down to the

desired height above the countertop. Tighten screws.

• Check to be sure the support frame is level,

vertically and horizontally.

Hood

Mounting

Flange

Lower Support

13-5/8

*39-1/8"

Air

Deflector

25-1/2" Recommended

**75-1/8"

to Floor

Upper

Plastic Upper

Front

Support

Duct Connector

Frame

Hood

Countertop

Support

Frame

Opening

Check Level in

Both Direction

Lower

Support

Frame

*Note: 39-1/8” to top of hood flange can be increased up to

42” max.

**75-1/8” min to floor, 77-7/8” max.

Important: Again, check to be sure the support is

level in both directions. There is no way to level the

hood after the hood is secured to the frame.

Installation Instructions

SECURE WIRING

SIZE AND INSTALL DUCTWORK

• Route house wiring through the ceiling hole and

pull a length to reach the hood junction box,

approximately 6″ below the support.

• Measure from top duct connector (Dim. A) to

bottom of support frame.

– Add at least 1″ for duct overlap at the top.

– Subtract 1-3/4″ for hood insertion into the bottom

of the frame.

Ceiling

• Cut the 6″ dia. duct to the required length.

Front Side

Ceiling

Support

Frames

Duct Connector

Tape

Side

View

Support

Required

Frame

Duct

Length

Dim. A

Duct

House

Wiring

Duct Connection

To Hood

1-3/4"

• Tape the wire to the front of the frame support to

prevent damage during installation and service.

Bottom Support

Frame Flange

Note: The top and bottom of the duct are external

(female) connections. The bottom end should be

flared slightly, to facilitate installation of the hood.

• Install duct up through support frames onto the top

duct connector. Push duct up until it is 1-3/4″ from

the bottom of support frame flange. See illustration.

Installation Instructions

INSTALL DECORATIVE DUCT COVERS

Top Duct

Cover

Install Screw on

Each Side

Pretap

2 Screw

Holes

Bottom Duct Cover

Top Duct

Cover

Bottom Duct

Cover

Top Duct

Cover

Stop Screw

Install Stop

Screw in One

of 3 Holes

• Pretap or drive decorative screw into the screw holes

on the support frame. This will make screw installation

easier.

• Separate the two decorative duct covers.

• Select the inside (top) cover, which has vent hole

pattern at the top.

• Slide the lower decorative duct over the installed upper

duct and push up, past the stop screw location.

• Install the supplied temporary stop screw in one of 3

holes in the support frame or the top duct cover to

prevent the bottom decorative duct cover from sliding

down.

• Slide the decorative duct cover over the support frame

and push to the ceiling.

• Attach to the hood support at the top with 2 supplied

decorative screws.

• Locate the stop screw in the envelope taped to the

front of the hood. Set aside.

CAUTION:

The stop screw must be installed.

Failure to do so could result in personal injury or damage

to the duct cover.

Installation Instructions

7 INSTALL HOOD

Bottom

Duct

Cover

Align Duct

Connector to

House Duct

Align

Mounting

Stop Screw

Studs

Install

4 lock

washer

and 4 Nuts

• Check hood level in both directions.

• Check to be sure that the duct is positioned over the

hood connector.

Note: TWO PEOPLE ARE REQUIRED TO COMPLETE

THIS INSTALLATION!

• Seal the duct connection with duct tape.

Note: Do not drive screws through this duct connection.

Doing so will prevent proper damper operation.

• Lift the hood up to the support frame. Carefully align

the hood mounting studs into the support frame holes,

and at the same time, guide the hood duct connector

into the duct.

• Install 4 nuts and lock washers. Tighten with a 10mm

wrench.

8 CONNECT ELECTRICAL

Verify that power is turned off at the source.

WARNING:

If house wiring is not 2-wire

with a ground wire, a ground must be provided by

the installer. When house wiring is aluminum, be

sure to use UL approved anti-oxidant compound and

aluminum-to-copper connectors.

• Install strain relief onto the knockout of the

junction box cover.

• Insert house wiring through strain relief and

tighten.

• Connect white leads to branch circuit white lead.

• Connect black leads to branch circuit black lead.

• Connect green/yellow leads to branch circuit green

or bare ground lead.

• Secure all connections with wire nuts on each

electrical connector.

• Push wires into junction box and replace cover. Be

sure wires are not pinched.

Installation Instructions

Install Charcoal Filters

9 SLIDE DUCT COVER DOWN,

INSTALL SIDE UTILITY BARS

Upper Charcoal

Filter Slots

Grasp Tab,

Lift and Pull Forward

• Remove protective film on charcoal filters.

• Tip charcoal filters into the upper (top) slots at the

rear of the opening. Grasp the filter tab, lift and

pull forward until it rests in the front slots.

• Install all 3 charcoal filters.

• Hold the decorative duct cover and remove the

temporary stop screw from the support frame.

Return the screw to the service manual envelope

for future use.

• Slide the lower duct cover down onto the hood.

Install Grease Filters

Lower

Filter Slots

• Remove protective film from grease filters.

• Tip the grease filter into the lower slots at the rear

of the opening. Lift the filter and pull the knob

forward until the filter rests on the slots.

• Install all 3 grease filters.

• Install the side utility bars with screws as shown.

• To remove the filters, grasp the knob, push the

filter towards the rear and tilt downwards. Grasp

tabs on charcoal filters, push towards the rear and

tilt downwards.

10 INSTALL FILTERS

Upper Charcoal

Filter Slots

Lower Grease

Filter Slots

11 FINALIZE INSTALLATION

• Remove the protective film covering the control

panel on the front face of the hood, and any other

packaging materials.

• Refer to the Owner’s Manual for operating

instructions.

• There are two slots inside the back and front of the

hood. These slots will hold the charcoal filters and

stainless steel grease filters in place.

Note: While performing installations described in this book,

safety glasses or goggles should be worn.

For Monogram local service in your area, call

1.800.444.1845.

Note: Product improvement is a continuing endeavor at

General Electric. Therefore, materials, appearance and

specifications are subject to change without notice.

Pub. No. 49-80045-2

04/07 JR

GE Consumer & Industrial

GE Appliances

General Electric Company

Louisville, KY 40225

Printed in Italy

monogram.com

Clover Electronics DVR CDR1650 User Manual
Cooper Lighting Indoor Furnishings VT2 User Manual
Cornelius Ice Maker 15303 User Manual
Craftsman Garage Door Opener 13953661SRT1 User Manual
Dacor Convection Oven DCM24 User Manual
Fellowes Paper Shredder M 7C User Manual
Fisher Price Automobile C3491 User Manual
Fisher Price Musical Toy Instrument Y6969 User Manual
FujiFilm Digital Camera 3100ixZ User Manual
Fujitsu Telephone SRS 9924 ABM User Manual